Never remove a component or plug unless you are certain all system pressure has been depleted.Ĩ. Never connect or disconnect a hose or line containing pressure it may whip. Never exceed manufacturer’s recommended pressures.ħ. Following the vehicle manufacturer’s recommended procedures, deactivate the electrical system in a manner that safely removes all electrical power from the vehicle.Ħ. If the vehicle is equipped with an AD-IS ® air dryer system or a dryer reservoir module, be sure to drain the purge reservoir.ĥ. If the work is being performed on the vehicle’s air brake system, or any auxiliary pressurized air systems, make certain to drain the air pressure from all reservoirs before beginning ANY work on the vehicle. Use only the proper tools and observe all precautions pertaining to use of those tools.Ĥ. Do not attempt to install, remove, disassemble or assemble a component until you have read and thoroughly understand the recommended procedures. Where circumstances require that the engine be in operation, EXTREME CAUTION should be used to prevent personal injury resulting from contact with moving, rotating, leaking, heated or electrically charged components.ģ. When working in the engine compartment, the engine should be shut off and the ignition key should be removed. Stop the engine and remove ignition key when working under or around the vehicle. Park the vehicle on a level surface, apply the parking brakes, and always block the wheels.
When working on or around a vehicle, the following general precautions should be observed at all times:ġ. WARNING! PLEASE READ AND FOLLOW THESE INSTRUCTIONS TO AVOID PERSONAL INJURY OR DEATH: A serviceable nylon filter to help prevent foreign material.Alocking dust cover to provide additional electrical connector.Give improved protection from water, etc. A pressure equalizing valve in the sealed ECU housing to.Support for Power Line Carrier (PLC) communication to the.
BENDIX ABS BLINK CODES CODE
Blink code diagnostics and support for advanced diagnosticĭiagnostic Trouble Code Detection.Optional mounting to the service reservoir or to the chassis,.6Įliminating the need for external pigtail harnesses. Internal electrical connections to the primary MRV,Ĭustomer Scratch Pad.The Premium TABS-6 module isĪuto-configurabletocontrolmoresensorsandmodulators(upto
Integrated into a single self-contained 2S/1M (two-sensor, one All modules include an ElectronicĬontrol Unit (ECU) and Modulator Relay Valve (MRV) which are The module acts as a relay valveĭuring normal braking, but during ABS events, it will intervene The Bendix ® TABS-6 module is an integrated trailer ABSĬontroller and modulator for air-braked heavy-duty trailers,Ĭomponents. All Rights Reserved.FIGURE 1 - TABS-6 standard and Premium MODULeS © Copyright Drakefield Limited 2007-2008. If code does not clear, it may be necessary to replace the ECUĬheck all ABS valve ground connections for diagonals 1 and 2 (open, shorted to ground or shorted to battery). Verify accuracy of blink code and clear from ECU memoryĬheck vehicle voltage, fuse, and supply to ECU (9.5-14 volts)Ĭheck vehicle voltage (9.5-14 volts for a 12-volt system, 18-30 volts for a 24-volt system) Verify blink code switch was activated longer than 16 seconds Verify 7 to 14 ohms resistance for a 12-volt system, 28-49 ohms resistance for a 24-volt system Repair or replace as neededĬheck for proper data link connection (J1922 and J1939)Ĭheck ATC Valve, valve cables, and connectors Verify minimum 0.2 volts AC output 30 RPMĬheck sensor, sensor cable, and connectorsĬheck for tyre size mismatch or tooth wheel differenceĬheck sensor, sensor cable, and connector for intermittent contactĬheck for damaged tooth wheel. Refer to service information provided by manufacturerĬheck for loose wheel bearings or excessive hub runout